Hobbs/VDO, tach time and airswitch?
Thread Starter
Join Date: Mar 2018
Location: Currently: A landlocked country with high terrain, otherwise Melbourne, Australia + Washington D.C.
Posts: 396
Likes: 0
Received 0 Likes
on
0 Posts
Hobbs/VDO, tach time and airswitch?
I (think that I) know the difference between these two times however when referring an aircraft to a 50 or 100 hourly maintenance, which time should be considered? Hobbs or tach?
Same question regarding overhauls. If your aircraft manufacturer states TBO: 2000 hours, is that in Hobbs or in tach time?
Also:
– It would seem that in Australia the Hobbs meter is usually called VDO. Is that correct?
– Is the tach time the same as an airswitch?
Same question regarding overhauls. If your aircraft manufacturer states TBO: 2000 hours, is that in Hobbs or in tach time?
Also:
– It would seem that in Australia the Hobbs meter is usually called VDO. Is that correct?
– Is the tach time the same as an airswitch?
That's not tach time.
It could be Hobbs time, but only if the Hobbs is connected to an air switch. Many Hobbs meters start counting and keep counting while ever the battery (and maybe master) switch is on.
Same question regarding overhauls. If your aircraft manufacturer states TBO: 2000 hours, is that in Hobbs or in tach time?
Also:
– It would seem that in Australia the Hobbs meter is usually called VDO. Is that correct?
– It would seem that in Australia the Hobbs meter is usually called VDO. Is that correct?
The confusion arises because a Hobbs meter is merely a brand. That brand can be connected to a master (and maybe master) switch and counts time while ever it's switched on, or can be connected to an airswitch and measures time in excess of a particular airspeed (based on the assumption that the aircraft is flying while ever that airspeed is exceeded).
– Is the tach time the same as an airswitch?
Tach time measures the time the engine is running. (Although it's worth noting that the time recorded on a tach is only accurate when the RPM is at the RPM for which the tach is calibrated. Below that RPM an hour of actual operation will be recorded as a shorter time on the tach, and above that RPM an hour of actual operation will be recorded as a longer time on the tach.)
Airswitch time measures the time from wheels off to wheels on, or pretty close to that.
It can be simplified further ...
Maintenance time is the time between the wheels leaving the ground and the wheels touching the ground. How this is recorded is up to the operator but could be taco, air switch or watch time.
What you pay for the aircraft is also an operator decision but is usually startup to shutdown time. Again, how this is recorded is up to the operator but a “Hobbs” (brand) meter is common, it starts when the oil pressure activates it and stops when the oil pressure stops.
The difference between the two is around 0.2 per sector or lesson. This “guestimate” is 6 minutes till airborne and 6 minites after landing till engine off. Pilots log time in command which is usually considered as startup till shutdown.
Maintenance time is the time between the wheels leaving the ground and the wheels touching the ground. How this is recorded is up to the operator but could be taco, air switch or watch time.
What you pay for the aircraft is also an operator decision but is usually startup to shutdown time. Again, how this is recorded is up to the operator but a “Hobbs” (brand) meter is common, it starts when the oil pressure activates it and stops when the oil pressure stops.
The difference between the two is around 0.2 per sector or lesson. This “guestimate” is 6 minutes till airborne and 6 minites after landing till engine off. Pilots log time in command which is usually considered as startup till shutdown.
Join Date: Jul 2006
Location: Australia
Posts: 325
Likes: 0
Received 0 Likes
on
0 Posts
Maintenance time is the time between the wheels leaving the ground and the wheels touching the ground. How this is recorded is up to the operator but could be taco, air switch or watch time.
Last edited by StickWithTheTruth; 12th Apr 2018 at 12:16.
Join Date: Sep 2002
Location: Australia
Posts: 1,082
Likes: 0
Received 0 Likes
on
0 Posts
Well lets see.
Pilots logbook is chock to chock.
Engine and/or airframe on tacho, Hobbs connected to battery or oil pressure or torque gauge line or air switch - it goes on.
All of these times are significantly different when recorded.
Friendly FOI visits and peruses the books.
Notes discrepancy in times recorded.
Does what FOI's do.
Operator now insists hours recorded must all line up.
Now which way do you think it will go?
Pilot logbook now on air switch? Or aircraft time in service chock to chock?
Hint - some of these recording means are very adjustable.
Pilots logbook is chock to chock.
Engine and/or airframe on tacho, Hobbs connected to battery or oil pressure or torque gauge line or air switch - it goes on.
All of these times are significantly different when recorded.
Friendly FOI visits and peruses the books.
Notes discrepancy in times recorded.
Does what FOI's do.
Operator now insists hours recorded must all line up.
Now which way do you think it will go?
Pilot logbook now on air switch? Or aircraft time in service chock to chock?
Hint - some of these recording means are very adjustable.
Aircraft 'time in service' has never been and never will be the same as the time recorded as time in command of the pilots of that aircraft.
Without going into the tedious detail and exceptions, the general rules are:
- aircraft time in service is measured from wheels off to wheels on
- pilot time in command/dual is measured chock to chock.
Accordingly, pilots can and should be recording more time in their logbooks for a flight than the 'time in service' recorded for the aircraft for that flight. The pilot is in command/dual for a longer period of time than just the period from wheels off to wheels on.
If some FOI reckons the numbers should match, the FOI is an arseclown.
Without going into the tedious detail and exceptions, the general rules are:
- aircraft time in service is measured from wheels off to wheels on
- pilot time in command/dual is measured chock to chock.
Accordingly, pilots can and should be recording more time in their logbooks for a flight than the 'time in service' recorded for the aircraft for that flight. The pilot is in command/dual for a longer period of time than just the period from wheels off to wheels on.
If some FOI reckons the numbers should match, the FOI is an arseclown.
Join Date: Sep 2002
Location: Australia
Posts: 1,082
Likes: 0
Received 0 Likes
on
0 Posts
It has been thus, longer than I care to mention.
Also, how the air switch is adjusted is shall we say far from standardised or tamper proof. Some may stop logging at TOD.
Also, how the air switch is adjusted is shall we say far from standardised or tamper proof. Some may stop logging at TOD.
Join Date: Jun 2010
Location: TinselTown
Age: 45
Posts: 203
Likes: 0
Received 0 Likes
on
0 Posts
That sort of time is usually for engines. If it's for an engine, tach time is the measure.
Join Date: Feb 2000
Location: Alaska, PNG, etc.
Age: 60
Posts: 1,550
Likes: 0
Received 0 Likes
on
0 Posts
Well lets see.
Pilots logbook is chock to chock.
Engine and/or airframe on tacho, Hobbs connected to battery or oil pressure or torque gauge line or air switch - it goes on.
All of these times are significantly different when recorded.
Friendly FOI visits and peruses the books.
Notes discrepancy in times recorded.
Does what FOI's do.
Operator now insists hours recorded must all line up.
Now which way do you think it will go?
Pilot logbook now on air switch? Or aircraft time in service chock to chock?
Hint - some of these recording means are very adjustable.
Pilots logbook is chock to chock.
Engine and/or airframe on tacho, Hobbs connected to battery or oil pressure or torque gauge line or air switch - it goes on.
All of these times are significantly different when recorded.
Friendly FOI visits and peruses the books.
Notes discrepancy in times recorded.
Does what FOI's do.
Operator now insists hours recorded must all line up.
Now which way do you think it will go?
Pilot logbook now on air switch? Or aircraft time in service chock to chock?
Hint - some of these recording means are very adjustable.
Join Date: Feb 2000
Location: Alaska, PNG, etc.
Age: 60
Posts: 1,550
Likes: 0
Received 0 Likes
on
0 Posts
Join Date: Feb 2000
Location: Alaska, PNG, etc.
Age: 60
Posts: 1,550
Likes: 0
Received 0 Likes
on
0 Posts
How do you adjust an airswitch so that it stops logging at TOD. Seems like you could conceivably set one so the it *only* logs time when the airspeed builds in the descent, but I'm not seeing how you could do it so that it *stops* logging when you push the nose over.
Join Date: Feb 2000
Location: Alaska, PNG, etc.
Age: 60
Posts: 1,550
Likes: 0
Received 0 Likes
on
0 Posts
Man Bilong Balus long PNG
Join Date: Apr 2002
Location: Back in Japan, flying the Glider Tug, eating great Japanese food, looking at lovely Japanese Ladies and continuing the neverending search for a bad bottle of Red.
Posts: 2,984
Received 111 Likes
on
64 Posts
Quite a few years ago now, I flew about four different Chieftains at various times. All had Hobbs meters fitted.
None of them worked!
BTW, MR time was wheels off to wheels on.
None of them worked!
BTW, MR time was wheels off to wheels on.
Every flight school I have dealt with has used only two separate timers for their maintenance and student (or hire & fly) billing.
For charging of students and hire & fly customers it was always hobbs time (engine start to engine stop).
The time recorded in the MR for maintenance purposes was always airswitch time (even on aircraft which also had tachometer). I have flown G1000 C172 aircraft which have the tacho time on the G1000 panel but we always recorded airswitch and hobbs only.
For charging of students and hire & fly customers it was always hobbs time (engine start to engine stop).
The time recorded in the MR for maintenance purposes was always airswitch time (even on aircraft which also had tachometer). I have flown G1000 C172 aircraft which have the tacho time on the G1000 panel but we always recorded airswitch and hobbs only.
Join Date: Sep 2002
Location: Australia
Posts: 1,082
Likes: 0
Received 0 Likes
on
0 Posts
So the answer to the OP's original question is....
You can pretty much do whatever suits you.
If you are an owner or operator seeking to maximise returns for hire, use a system that tends to over read.
If you are an operator seeking to minimise costs, use a system that tends to under read.
Using a combination of both? Pure genius
If you are a line pilot seeking to comply with regs but stay employed, well, that can be awkward.
You can pretty much do whatever suits you.
If you are an owner or operator seeking to maximise returns for hire, use a system that tends to over read.
If you are an operator seeking to minimise costs, use a system that tends to under read.
Using a combination of both? Pure genius
If you are a line pilot seeking to comply with regs but stay employed, well, that can be awkward.